Hallo zusammen,
ich brauche jetzt mal Hilfe. Folgende Situation:
W98 auf C:
Linux auf D:
Die Installation verläuft problemlos, Am Abschluß wird die Einrichtung von LILO angeboten. LILO wird dann auf hdd = D: installiert. Boote ich
diese Platte durch Umstellung im BIOS auf HD1, dann bricht das Laden von LILO mit der Meldung "L01 01 01 01 ..." ab. Ich habe die LILO.CONF
mal umgeschrieben, so dass mit dem Befehl /sbin/lilo auf hda = c: installiert wird. Aber auch hier das gleiche Problem. Mit der Bootdiskette
startet Linux ohne Probleme.
Meine Fragen:
1. Kann ich nicht einfach den MBR von der Bootdiskette auf hdd schreiben. Würde dann einfach über das BIOS das Firstboot-Device umstellen, wenn
ich W98 oder Linux booten will. Für W98 gibt es solche Tools zum Auslesen und Schreiben des MBRs. Schöner wäre es natürlich wenn es wie bei
2. ginge...
2. LILO im MBR wäre die tollste Lösung. Ich denke es liegt an der LILO.CONF. Ja, die Zielplatte ist hier noch auf hdd eingestellt. Vielleicht
schaut mal einer über meine LILO.CONF.
----------------------------------------- schnipp LILO.CONF Anfang -----------------------
vga=791
# /etc/lilo.conf - See: `lilo(8)\' and `lilo.conf(5)\',
# --------------- `install-mbr(8)\', `/usr/share/doc/lilo/\',
# and `/usr/share/doc/mbr/\'.
# +---------------------------------------------------------------+
# | !! Reminder !! |
# | |
# | Don\'t forget to run `lilo\' after you make changes to this |
# | conffile, `/boot/bootmess.txt\', or install a new kernel. The |
# | computer will most likely fail to boot if a kernel-image |
# | post-install script or you don\'t remember to run `lilo\'. |
# | |
# +---------------------------------------------------------------+
# Support LBA for large hard disks.
#
lba32
# Overrides the default mapping between harddisk names and the BIOS\'
# harddisk order. Use with caution.
#disk=/dev/hde
# bios=0x81
#disk=/dev/sda
# bios=0x80
# Specifies the boot device. This is where Lilo installs its boot
# block. It can be either a partition, or the raw device, in which
# case it installs in the MBR, and will overwrite the current MBR.
#
boot=/dev/hdd
# Specifies the device that should be mounted as root. (`/\')
#
root=/dev/hdd1
# Enable map compaction:
# Tries to merge read requests for adjacent sectors into a single
# read request. This drastically reduces load time and keeps the
# map smaller. Using `compact\' is especially recommended when
# booting from a floppy disk. It is disabled here by default
# because it doesn\'t always work.
#
# compact
# Installs the specified file as the new boot sector
# You have the choice between: bmp, compat, menu and text
# Look in /boot/ and in lilo.conf(5) manpage for details
#
install=/boot/boot-menu.b
# Specifies the location of the map file
#
map=/boot/map
# You can set a password here, and uncomment the `restricted\' lines
# in the image definitions below to make it so that a password must
# be typed to boot anything but a default configuration. If a
# command line is given, other than one specified by an `append\'
# statement in `lilo.conf\', the password will be required, but a
# standard default boot will not require one.
#
# This will, for instance, prevent anyone with access to the
# console from booting with something like `Linux init=/bin/sh\',
# and thus becoming `root\' without proper authorization.
#
# Note that if you really need this type of security, you will
# likely also want to use `install-mbr\' to reconfigure the MBR
# program, as well as set up your BIOS to disallow booting from
# removable disk or CD-ROM, then put a password on getting into the
# BIOS configuration as well. Please RTFM `install-mbr(8)\'.
#
# password=tatercounter2000
# Specifies the number of deciseconds (0.1 seconds) LILO should
# wait before booting the first image.
#
delay=20
# You can put a customized boot message up if you like. If you use
# `prompt\', and this computer may need to reboot unattended, you
# must specify a `timeout\', or it will sit there forever waiting
# for a keypress. `single-key\' goes with the `alias\' lines in the
# `image\' configurations below. eg: You can press `1\' to boot
# `Linux\', `2\' to boot `LinuxOLD\', if you uncomment the `alias\'.
#
# message=/boot/bootmess.txt
prompt
timeout=150
# prompt
# single-key
# delay=100
# timeout=100
# Kernel command line options that apply to all installed images go
# here. See: The `boot-prompt-HOWO\' and `kernel-parameters.txt\' in
# the Linux kernel `Documentation\' directory.
#
# append=""
append="hda=scsi hdb=scsi hdc=scsi hdd=scsi hde=scsi hdf=scsi hdg=scsi hdh=scsi apm=power-off nomce"
# Boot up Linux by default.
#
default=Linux
image=/boot/vmlinuz-2.4.20-xfs
label=Linux
initrd=/boot/initrd.gz
read-only
# restricted
# alias=1
image=/vmlinuz.old
label=LinuxOLD
read-only
optional
# restricted
# alias=2
# If you have another OS on this machine to boot, you can uncomment the
# following lines, changing the device name on the `other\' line to
# where your other OS\' partition is.
#
# other=/dev/hda4
# label=HURD
# restricted
# alias=3
other=/dev/hda1
label="Windows(hda1)"
-------------------------------------------- schnipp Ende der LILO.CONF --------------------------------------------
Also, erstmal vielen Dank für alle Antworten.
Steffen
// Möge das bessere Betriebssytem gewinnen ;-) //
Steffen1111
