Hi,
bin bei der Installation meiner terratec base 1 soundkarte unter Linux SuSE 6.1....
pnpdump liefert folgende ausgabre :
$Id: pnpdump.c,v 1.20 1999/12/02 22:39:24 fox Exp $
# Release isapnptools-1.20
# This is free software, see the sources for details.
# This software has NO WARRANTY, use at your OWN RISK
#
# For details of this file format, see isapnp.conf(5)
#
# For latest information and FAQ on isapnp and pnpdump see:
# http://www.roestock.demon.co.uk/isapnptools/
#
# Compiler flags: -DREALTIME -DNEEDSETSCHEDULER -DABORT_ONRESERR
#
# Trying port address 0273
# Board 1 has serial identifier c6 ff ff ff ff 11 14 b2 50
# (DEBUG)
(READPORT 0x0273)
(ISOLATE PRESERVE)
(IDENTIFY *)
(VERBOSITY 2)
(CONFLICT (IO FATAL)(IRQ FATAL)(DMA FATAL)(MEM FATAL)) # or WARNING
# Card 1: (serial identifier c6 ff ff ff ff 11 14 b2 50)
# Vendor Id TER1411, No Serial Number (-1), checksum 0xC6.
# Version 1.0, Vendor version 1.1
# ANSI string -->TERRATEC SOUNDSYSTEM BASE 1#
# Logical device id ADS7180
# Device supports I/O range check register
# Device supports vendor reserved register @ 0x3b
# Device supports vendor reserved register @ 0x3c
# Device supports vendor reserved register @ 0x3d
# Device supports vendor reserved register @ 0x3e
#
# Edit the entries below to uncomment out the configuration required.
# Note that only the first value of any range is given, this may be changed if required
# Don't forget to uncomment the activate (ACT Y) when happy
(CONFIGURE TER1411/-1 (LD 0
# Multiple choice time, choose one only !
# Start dependent functions: priority preferred
# IRQ 5.
# High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 5 (MODE +E)))
# First DMA channel 1.
# 8 bit DMA only
# Logical device is a bus master
# DMA may execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed type F
# (DMA 0 (CHANNEL 1))
# Next DMA channel 3.
# 8 bit DMA only
# Logical device is a bus master
# DMA may execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed type F
# (DMA 1 (CHANNEL 3))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0220
# Maximum IO base address 0x0220
# IO base alignment 32 bytes
# Number of IO addresses required: 16
# (IO 0 (SIZE 16) (BASE 0x0220) (CHECK))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0388
# Maximum IO base address 0x0388
# IO base alignment 8 bytes
# Number of IO addresses required: 4
# (IO 1 (SIZE 4) (BASE 0x0388) (CHECK))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0530
# Maximum IO base address 0x0530
# IO base alignment 8 bytes
# Number of IO addresses required: 16
# (IO 2 (SIZE 16) (BASE 0x0530) (CHECK))
# Start dependent functions: priority acceptable
# IRQ 5 or 7.
# High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 5 (MODE +E)))
# First DMA channel 0, 1 or 3.
# 8 bit DMA only
# Logical device is a bus master
# DMA may execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed type F
# (DMA 0 (CHANNEL 0))
# Next DMA channel 0, 1 or 3.
# 8 bit DMA only
# Logical device is a bus master
# DMA may execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed type F
# (DMA 1 (CHANNEL 0))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0220
# Maximum IO base address 0x0240
# IO base alignment 32 bytes
# Number of IO addresses required: 16
# (IO 0 (SIZE 16) (BASE 0x0220) (CHECK))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0388
# Maximum IO base address 0x0388
# IO base alignment 8 bytes
# Number of IO addresses required: 4
# (IO 1 (SIZE 4) (BASE 0x0388) (CHECK))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0530
# Maximum IO base address 0x0530
# IO base alignment 16 bytes
# Number of IO addresses required: 16
# (IO 2 (SIZE 16) (BASE 0x0530) (CHECK))
# Start dependent functions: priority functional
# IRQ 5, 7 or 10.
# High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 5 (MODE +E)))
# First DMA channel 0, 1 or 3.
# 8 bit DMA only
# Logical device is a bus master
# DMA may execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed type F
# (DMA 0 (CHANNEL 0))
# Next DMA channel 0, 1 or 3.
# 8 bit DMA only
# Logical device is a bus master
# DMA may execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed type F
# (DMA 1 (CHANNEL 0))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0220
# Maximum IO base address 0x0280
# IO base alignment 32 bytes
# Number of IO addresses required: 16
# (IO 0 (SIZE 16) (BASE 0x0220) (CHECK))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0388
# Maximum IO base address 0x03b8
# IO base alignment 8 bytes
# Number of IO addresses required: 4
# (IO 1 (SIZE 4) (BASE 0x0388) (CHECK))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0500
# Maximum IO base address 0x0560
# IO base alignment 16 bytes
# Number of IO addresses required: 16
# (IO 2 (SIZE 16) (BASE 0x0500) (CHECK))
# Start dependent functions: priority functional
# IRQ 5, 7, 10 or 11.
# High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 5 (MODE +E)))
# First DMA channel 0, 1 or 3.
# 8 bit DMA only
# Logical device is a bus master
# DMA may execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed type F
# (DMA 0 (CHANNEL 0))
# *** ERROR *** No DMA channel specified!
# 8 bit DMA only
# Logical device is a bus master
# DMA may execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed type F
# (DMA 1 (CHANNEL 4))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0220
# Maximum IO base address 0x0280
# IO base alignment 32 bytes
# Number of IO addresses required: 16
# (IO 0 (SIZE 16) (BASE 0x0220) (CHECK))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0388
# Maximum IO base address 0x03b8
# IO base alignment 8 bytes
# Number of IO addresses required: 4
# (IO 1 (SIZE 4) (BASE 0x0388) (CHECK))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0500
# Maximum IO base address 0x0620
# IO base alignment 16 bytes
# Number of IO addresses required: 16
# (IO 2 (SIZE 16) (BASE 0x0500) (CHECK))
# Start dependent functions: priority functional
# IRQ 5, 7, 9, 10, 11 or 15.
# High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 5 (MODE +E)))
# First DMA channel 0, 1 or 3.
# 8 bit DMA only
# Logical device is a bus master
# DMA may execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed type F
# (DMA 0 (CHANNEL 0))
# *** ERROR *** No DMA channel specified!
# 8 bit DMA only
# Logical device is a bus master
# DMA may execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed type F
# (DMA 1 (CHANNEL 4))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0220
# Maximum IO base address 0x0280
# IO base alignment 32 bytes
# Number of IO addresses required: 16
# (IO 0 (SIZE 16) (BASE 0x0220) (CHECK))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0388
# Maximum IO base address 0x03b8
# IO base alignment 8 bytes
# Number of IO addresses required: 4
# (IO 1 (SIZE 4) (BASE 0x0388) (CHECK))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0500
# Maximum IO base address 0x0620
# IO base alignment 16 bytes
# Number of IO addresses required: 16
# (IO 2 (SIZE 16) (BASE 0x0500) (CHECK))
# End dependent functions
(NAME "TER1411/-1[0]{TERRATEC SOUNDSYSTEM BASE 1}")
# (ACT Y)
))
#
# Logical device id ADS7181
# Device supports I/O range check register
# Device supports vendor reserved register @ 0x3b
# Device supports vendor reserved register @ 0x3c
# Device supports vendor reserved register @ 0x3d
# Device supports vendor reserved register @ 0x3e
#
# Edit the entries below to uncomment out the configuration required.
# Note that only the first value of any range is given, this may be changed if required
# Don't forget to uncomment the activate (ACT Y) when happy
(CONFIGURE TER1411/-1 (LD 1
# Compatible device id PNPb006
# Multiple choice time, choose one only !
# Start dependent functions: priority preferred
# IRQ 9.
# High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 9 (MODE +E)))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0330
# Maximum IO base address 0x0330
# IO base alignment 16 bytes
# Number of IO addresses required: 2
# (IO 0 (SIZE 2) (BASE 0x0330) (CHECK))
# Start dependent functions: priority acceptable
# IRQ 9.
# High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 9 (MODE +E)))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0300
# Maximum IO base address 0x0330
# IO base alignment 16 bytes
# Number of IO addresses required: 2
# (IO 0 (SIZE 2) (BASE 0x0300) (CHECK))
# Start dependent functions: priority functional
# IRQ 9, 10, 11 or 15.
# High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 9 (MODE +E)))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0300
# Maximum IO base address 0x0330
# IO base alignment 16 bytes
# Number of IO addresses required: 2
# (IO 0 (SIZE 2) (BASE 0x0300) (CHECK))
# End dependent functions
(NAME "TER1411/-1[1]{TERRATEC SOUNDSYSTEM BASE 1}")
# (ACT Y)
))
#
# Logical device id ADS7182
# Device supports I/O range check register
# Device supports vendor reserved register @ 0x3b
# Device supports vendor reserved register @ 0x3c
# Device supports vendor reserved register @ 0x3d
# Device supports vendor reserved register @ 0x3e
#
# Edit the entries below to uncomment out the configuration required.
# Note that only the first value of any range is given, this may be changed if required
# Don't forget to uncomment the activate (ACT Y) when happy
(CONFIGURE TER1411/-1 (LD 2
# Compatible device id PNPb02f
# Multiple choice time, choose one only !
# Start dependent functions: priority preferred
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0200
# Maximum IO base address 0x0200
# IO base alignment 8 bytes
# Number of IO addresses required: 8
# (IO 0 (SIZE 8) (BASE 0x0200) (CHECK))
# Start dependent functions: priority acceptable
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0200
# Maximum IO base address 0x0208
# IO base alignment 8 bytes
# Number of IO addresses required: 8
# (IO 0 (SIZE 8) (BASE 0x0200) (CHECK))
# End dependent functions
(NAME "TER1411/-1[2]{TERRATEC SOUNDSYSTEM BASE 1}")
# (ACT Y)
))
#
# Logical device id TER2211
# Device supports I/O range check register
# Device supports vendor reserved register @ 0x3b
# Device supports vendor reserved register @ 0x3c
# Device supports vendor reserved register @ 0x3d
# Device supports vendor reserved register @ 0x3e
#
# Edit the entries below to uncomment out the configuration required.
# Note that only the first value of any range is given, this may be changed if required
# Don't forget to uncomment the activate (ACT Y) when happy
(CONFIGURE TER1411/-1 (LD 3
# Multiple choice time, choose one only !
# Start dependent functions: priority preferred
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0590
# Maximum IO base address 0x0590
# IO base alignment 8 bytes
# Number of IO addresses required: 8
# (IO 0 (SIZE 8) (BASE 0x0590) (CHECK))
# Start dependent functions: priority acceptable
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0590
# Maximum IO base address 0x05a8
# IO base alignment 8 bytes
# Number of IO addresses required: 8
# (IO 0 (SIZE 8) (BASE 0x0590) (CHECK))
# Start dependent functions: priority functional
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0590
# Maximum IO base address 0x05c8
# IO base alignment 8 bytes
# Number of IO addresses required: 8
# (IO 0 (SIZE 8) (BASE 0x0590) (CHECK))
# End dependent functions
(NAME "TER1411/-1[3]{TERRATEC SOUNDSYSTEM BASE 1}")
# (ACT Y)
))
# End tag... Checksum 0x00 (OK)
# Returns all cards to the "Wait for Key" state
(WAITFORKEY)
aber was soll ich nun an dieser datei verändern... ???
Tertia (Anonym)
